 | #308351B 36x50 2x3 GRN Weld Wire
Brand: Midwest Air Technologies Part Number: 308351B
36" x 50', 2 x 3 Green PVC Welded Wire, 16 Gauge. | *$42.52 |
 | #308361B 36x50 3x2Mesh Weld Wire
Brand: Midwest Air Technologies Part Number: 308361B
Economy Fence, 36" x 50', 3" x 2" Mesh, Galvanized Welded Wire, 16 Gauge. | *$32.57 |
 | - Woods-N-Water Plotmaster - 3-Point, Category 1, 6ft. Length
Brand: Woods-n-Water
The Plotmaster III is a multi-use, all-in-one harrow/plow/cultivator/seeder/cultipacke r/drag with metal grating. Its expanded capabilities require a 30 HP or larger tractor. The Plotmaster III is designed to plow 72in. wide, cut 68in. wide and seed 60in. wide. Seeder attachment boasts a 150-lb. capacity. Made of heavy-duty steel components and comes with a 3-point hitch, so no electric lift system is needed. Ideal for establishing and maintaining large gardens, fields and foodplots. U.S.A. Hitch Type: 3-Point, Category Type: 1, Working Width (in.): Plow - 72, Cut - 68, Seed - 60, Required HP: 30, Blades (qty.): 8 -18 Notched Discs, 5 - S Tines | *$5,999.99 |
 | 1" x 72" San Angelo Bar
Brand: Truper Herramientas Model: BAP-175-C/32474 Part Number: BAP175C
1" x 72" San Angelo Bar, Press Or Drop Forged With Rust Resistant Black Finish For Superior Durability. | *$27.23 |
 | 1'W Machinery Wire Fence Partition Panel
Brand: Wireway Husky Part Number: G0105
Machinery Partition Panel Provides a barrier between employees and potential hazards. Meets OSHA regulations for guarding dangerous machinery, conveyor belts and electrical switchgear and EPA hazardous waste storage standards. Durable woven 10 gauge wire construction provides clear visibility. Partitions can be easily installed for quick removal or more permanently for maximum security with all supplied hardware. Panels measure 5'H and attach to post 1' above floor for sweep space. Easy to install, remove or expand. Bright yellow enamel finish. | *$47.95 |
 | 1.5" Brown Polytape for Electric Fence
Brand: LACME
You are looking at a roll of 1 1/2 inch Brown polytape with 13 stainless steel wires for excellent shocking ability. This is a tape great for areas that demand a low tone or earth colors. Environmentally friendly and excellent for horse pastures in residential areas. This polytape has 13 stainless steel wires for excellent conductivity with a breakstrength of 530 lbs and comes in rolls of 656 feet. This is one of our best selling 1.5 inch polytapes. | *$46.00 |
 | 1.5" Green Polytape for Electric Fence
Brand: LACME
You are looking at a roll 1.5 inch Green Polytape. Excellent for a temporary fence or use as a cross fence in areas that require environmentally friendly earth tone colors. Great for pastures or runways. This polytape has 8 tinned copper wires for excellent conductivity with a breakstrength of 530 lbs. | *$48.00 |
 | 1.5" White Polytape for Electric Fence
Brand: LACME
1.5 inch white polytape with 13 stainless steel wires. Very good tape at a very reasonable price. | *$38.00 |
 | 1.5" White Polytape w/ Blue trim for Electric Fence
Brand: LACME
You are looking at a roll of Rublanc 40, 1 1/2 inch polytape. It is actually just over 1 1/2 wide and has 10 tinned copper wires. This is an excellent high quality tape for horses. It makes a very attractive fence when used as perimeter or cross fence. This Polytape is excellent when used to divide up pastures, horse fences, traffic lanes and controlled grazing. It has a UV inhibitor added to extend its life. | *$48.00 |
 | 1/2" Blue Polytape for Electric Fence
Brand: LACME
You are looking at a roll of 1/2" Blue polytape (actually just under 1/2"). This tape is excellent for use in temporary fencing, controlled grazing or along old fences to keep animals off the fence. This polytape has 5 tinned copper wires for excellent conductivity with a breakstrength of 250 lbs. | *$18.00 |
| 1/2" Blue Polytape for Electric Fence
Brand: LACME
You are looking at a roll of 1/2" Blue polytape (actually just under 1/2"). This tape is excellent for use in temporary fencing, controlled grazing or along old fences to keep animals off the fence. This polytape has 5 tinned copper wires for excellent conductivity with a breakstrength of 250 lbs. | *$18.00 |
 | 1/2" White Polytape for Electric Fence
Brand: LACME
You are looking at a roll of 1/2 inch Polytape with 4 stainless steel wires and is one of the least expensive tapes on the market. This Polytape is excellent for temporary fence or controlled grazing. It is very easy to re-spool and it has a UV inhibitor added to extend its life. It has 185 lb breakstrength. | *$18.50 |
 | 10 7/16" Heavy Duty Fencesld Joint Pliers Carded (181-193610VN) Category: Fencing Pliers
Brand: Cooper Hand Tools Part Number: 193610VN
Item #: 181-193610VN. 2 staple grips in nosebrCorrugated hammer head with heavy prong to easily reach and pull rusty staplesbrSpecial openings in head allows both wire and staple to be grippedbr2 Electronically induction hardened durable wire cuttersbrPolished head pulliPacking Type = CardedliOverall Length = 10 7/16 inliJaw Length = 1 1/16 inliJaw Width = 3 5/8 inliJaw Thickness = 19/32 inliJaw Shape = CurvedliHandle Type = Cushion GripliMaterial = Forged Alloy SteelliType = Fence PliersliWt. = 24.96 oz/ul brCustomers also search for: Discount 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, Buy 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, Wholesale 10 7/16" Heavy Duty Fencesld Joint Pliers Carded, 037103212955, 193610VN, Fencing Pliers | *$23.21 |
 | 10 each: American Posts Light Duty U- Post (810-36-14)
Brand: American Model: 810-36-14 Part Number: 810-36-14
Sold as 10 each. 3 ft. Dimensions are 36"L x 1.3"W x 0.5"H. 14 gauge. U-channel construction for maximum strength. Ideal for lightweight, temporary fencing around trees, bushes, flowers and gardens. Powder coated finish-green color. Manufacturer number: 810-36-14. SKU #: 72506. Country of origin: (TBA). Distributed by . | *$31.99 |
 | 10 each: American Posts Light Duty U- Post (810-48-14)
Brand: American Model: 810-48-14 Part Number: 810-48-14
Sold as 10 each. 4 ft. Dimensions are 48"L x 1.3"W x 0.5"H. 14 gauge. Each post is 1.8 lbs. U-channel construction for maximum strength. Ideal for lightweight, temporary fencing around trees, bushes, flowers and gardens. Powder coated finish-green color. Manufacturer number: 810-48-14. SKU #: 72509. Country of origin: (TBA). Distributed by . | *$37.99 |
 | 10 each: American Posts Light Duty U- Post (810-60-14)
Brand: American Model: 810-60-14 Part Number: 810-60-14
Sold as 10 each. 5 ft. Dimensions are 60"L x 1.3"W x 0.5"H. 14 gauge. U-channel construction for maximum strength. Ideal for lightweight, temporary fencing around trees, bushes, flowers and gardens. Powder coated finish-green color. Manufacturer number: 810-60-14. SKU #: 72510. Country of origin: (TBA). Distributed by . | *$51.99 |
 | 10" Fence Plier - No Cutters
Brand: Raffael Tools Part Number: pli-f10
- Drop Forgedbr - Heat Treatedbr - Cushion Gripbr Weight: 1.85 Lbs | *$6.45 |
 | 10" Fence Plier With Side Cutters
Brand: Raffael Tools Part Number: pli-f10-sc
- Drop Forgedbr - Heat Treatedbr - Cushion Gripbr - 2 Side Cutters br Weight: 1.85 Lbs | *$6.96 |
 | 10"x10' GRN Fold Fence
Brand: Import Model: 901208A Part Number: 901208A
10" x 10', Green, Round Top, PVC Coated, Folding Fence. | *$4.09 |
| 10'W Machinery Wire Fence Partition Panel
Brand: Wireway Husky Part Number: G1005
Machinery Partition Panel Provides a barrier between employees and potential hazards. Meets OSHA regulations for guarding dangerous machinery, conveyor belts and electrical switchgear and EPA hazardous waste storage standards. Durable woven 10 gauge wire construction provides clear visibility. Partitions can be easily installed for quick removal or more permanently for maximum security with all supplied hardware. Panels measure 5'H and attach to post 1' above floor for sweep space. Easy to install, remove or expand. Bright yellow enamel finish. | *$180.95 |
 | 12"x12" Vacuum Form Machine - Plastic Former for Model, Mold, and Prototype Forming
Brand: WidgetWorks Unlimited Model: 12x12 Table Top Vacuum Fo Part Number: 12x12 Table Top Vacuum Fo
Our 12"x12" Table Top Vacuum Former is perfect for small businesses and hobbyists who want to create parts in plastic up to 1/8" thick. Produce intricate shapes with results that rival expensive commercial machines in their incredible accuracy and detail: prototypes, custom packaging, RC car bodies, model rocket nose cones, molds for plaster or concrete, chocolate and candy, candles, and soap making. Our 12"x12" Vacuum former includes a perforated aluminum vacuum platen (the top surface that delivers the vacuum under the hot plastic) that is computer designed and precision CNC machined to maximize air flow and eliminate unnecessary volume - both critical to rapid air evacuation and professional vacuum forming results. Detailed, step-by-step instructions along with sources for vacuum formable plastics are included. Compatible with all types of thermoform plastic: ABS, Acrylic (Plexiglas), Butyrate, PET-G, Polycarbonate (Lexan), Polyethylene, PVC, Styrene, Vinyl, etc. Requires house hold oven and Shop-Vac style vacuum cleaner with 1 1/4" hose/adapter. Vacuum Forming Explained in 3 Easy Steps: Step #1: Secure your plastic between the vacuum former's metal frames. Attach your Shop-Vac (not included) to the vacuum former. Place your model on top of the perforated aluminum vacuum platen. Step #2: Place the plastic in your kitchen oven and watch as it becomes soft and begins to sag. Align the metal frames with the vacuum former's guides and lower the plastic over your model. Step #3: The hot plastic forms an air tight seal around the vacuum platen's edges. Vacuum pressure pulls the hot plastic down around the model. After cooling for a few seconds the plastic part is complete. | *$89.95 |
 | 12"x18" Vacuum Form Machine - Plastic Former for Model, Mold, and Prototype Forming
Brand: WidgetWorks Unlimited Model: 12x18 Table Top Vacuum Fo Part Number: 12x18 Table Top Vacuum Fo
Our 12"x18" Table Top Vacuum Former is perfect for small businesses and hobbyists who want to create parts in plastic up to 1/8" thick. Produce intricate shapes with results that rival expensive commercial machines in their incredible accuracy and detail: prototypes, custom packaging, RC car bodies, model rocket nose cones, molds for plaster or concrete, chocolate and candy, candles, and soap making. Our 12"x18" Vacuum former includes a perforated aluminum vacuum platen (the top surface that delivers the vacuum under the hot plastic) that is computer designed and precision CNC machined to maximize air flow and eliminate unnecessary volume - both critical to rapid air evacuation and professional vacuum forming results. Detailed, step-by-step instructions along with sources for vacuum formable plastics are included. Compatible with all types of thermoform plastic: ABS, Acrylic (Plexiglas), Butyrate, PET-G, Polycarbonate (Lexan), Polyethylene, PVC, Styrene, Vinyl, etc. Requires house hold oven and Shop-Vac style vacuum cleaner with 1 1/4" hose/adapter. Vacuum Forming Explained in 3 Easy Steps: Step #1: Secure your plastic between the vacuum former's metal frames. Attach your Shop-Vac (not included) to the vacuum former. Place your model on top of the perforated aluminum vacuum platen. Step #2: Place the plastic in your kitchen oven and watch as it becomes soft and begins to sag. Align the metal frames with the vacuum former's guides and lower the plastic over your model. Step #3: The hot plastic forms an air tight seal around the vacuum platen's edges. Vacuum pressure pulls the hot plastic down around the model. After cooling for a few seconds the plastic part is complete. | *$139.95 |
 | 13,000 Watt P.T.O. Generator
Brand: NorthStar
Single-phase generator cranks out 100 Amps @ 120V, 50 Amps @ 240V. Requires 24 PTO HP or more for rated output: 13,000 surge Watts and 12,000 continuous Watts. Industry standard 1 3/8in., 6-spline input shaft is geared for 540 RPM. 100in. copper windings, metal construction, 100 Amp thermal magnetic breaker and plastic shield provide high performance, durability, long life and safe operation. Outlets include welding receptacle and four 120V 20 Amp receptacles and voltmeter. Pushbutton reset circuit breakers and 2-year warranty. Truck Ship. | *$1,299.99 |
 | 16 Piece Auger Bit Set
Brand: Eastern Steel Part Number: RC-A015P
Bore clean, deep holes in soft or hard wood with virtually no effort! For running electrical wires through floor joists, assembling 2x4 wood playsets for the kids and other tasks, these auger bits make the job a snap! Put some excitement into your next boring job with this tradesman's quality 16-pc. set. Each bit is forged from #45 carbon steel and has a heat-treated to HRC47 hardness tip, flutes ground behind the lands to pull chips up for fast, clean cutting and a polished finish. Includes 3/8, 1/2, 5/8, 3/4, 7/8 and 1 bits in both 4-3/4 and 8 lengths and 1/2, 5/8 and 3/4 bits in 16 length. Bits come in protective case. | *$29.99 |
 | 16x12 WHT Trim Fence
Brand: Greenes Fence Model: RC24W Part Number: RC 24W
16" x 12', White, Gothic Top Trim Fence, Trims Driveways Walkways, Protects Plants, Vegetables, Flowers, Young Shrubs Trees. | *$19.18 |
 | 18x8GRN Goth Fold Fence
Brand: Import Part Number: 901212A
18" x 8', Green, Gothic Top, PVC Coated, Folding Fence. | *$6.37 |
 | 190066 4X50ft. Green Fence - Tenax Corp - Landware
Brand: LandWare Model: 190066 Part Number: 190066
"LANDWARE" SNOW-GUARD FENCE
4' x 50'
Has a good porosity factor for storing snow
Economical enough for use by homeowners to control drifting on driveways and walkways
High density polyethylene
Green
Shrink-wrapped Retailer demand for dark color snow fence in Northern climate. | *$34.49 |
 | 2" Mega Polytape for Electric Fence
Brand: LACME
2 inch wide tape with 14 tin coated wires. This is an excellent tape for any of your fencing applications. It has very good wear characteristics and blue border for better visibility. | *$55.00 |
 | 2" Polytape insulator for Electric Fence - Black
Brand: Woodstream
Snap on "T" post insulator for 2" tape. It has a tight fit so insulator doesn't pop off. Even though the picture is of a white insulator, you are buying a pack of 25 black insulators. The 25 pack weighs 1.5lbs. | *$6.50 |
| 2" Polytape insulator for Electric Fence - White
Brand: Woodstream
Snap on white "T" post insulator for 2" tape. It has a tight fit so insulator doesn't pop off. The 25 pack weighs 1.5lbs. | *$6.50 |
 | 2" Reinforced Mega Polytape for Electric Fence
Brand: LACME
2 inch wide Reinforced tape with 14 tin coated wires. This is an excellent tape for any of your fencing applications. It has very good wear characteristics and blue border for better visibility. | *$75.00 |
| 2'W Machinery Wire Fence Partition Panel
Brand: Wireway Husky Part Number: G0205
Machinery Partition Panel Provides a barrier between employees and potential hazards. Meets OSHA regulations for guarding dangerous machinery, conveyor belts and electrical switchgear and EPA hazardous waste storage standards. Durable woven 10 gauge wire construction provides clear visibility. Partitions can be easily installed for quick removal or more permanently for maximum security with all supplied hardware. Panels measure 5'H and attach to post 1' above floor for sweep space. Easy to install, remove or expand. Bright yellow enamel finish. | *$52.95 |
 | 20ft NEW Steel Storage Container
Brand: ASCC 1-866-726-5067
This container is located in Long Beach CA We sell containers in 43 other location please acquire for other locations. Shipping using a tilt bed truck is available please contact me for a quote on trucking. 1-866-901-4526. This sale is for one NEW 20 foot Cargo Box / Shipping Container. These containers can be used for many uses such as:Backyard Storage, Temporary Offices or Storage for Construction Sites. The typical dimensions of a 20 foot container are 20'-0" in length 8'-0 width and 8'-6 in height. These boxes are very well constructed as they were made to be stacked up to 6 containers high on ships that travel across oceans. They are constructed with a steel frame, steel siding and the floors are constructed of 18 ply epoxy marine plywood. The picture shown may not the actual container for sale but is consistent with the type of containers we sell. | *$2,750.00 |
 | 24"x10' WHT Fold Fence
Brand: Import Part Number: 901219A
24" x 10', White, Round Top, PVC Coated, Folding Fence. | *$74.41 |
 | 25 each: Smv Electric Fence Post (3/8RB)
Brand: Smv Industries, Inc Model: 3/8RB Part Number: 3/8RB
Sold as 25 each. 48" long. 3/8" Dia. Rebar Rod. 4-1/2" anchor plate. Red. Bulk . Manufacturer number: 3/8RB. SKU #: 7018468. Country of origin: (TBA). Distributed by Smv Industries, Inc. | *$59.89 |
 | 25CT YEL TPost Extender
Brand: DARE Part Number: SNUG-X5TP-25
25 Count, Yellow, Snug T-Post Insulator Extender, Extends Wire 5" From Post, For 1.25 1.33 Posts. | *$7.64 |
 | 28IN. X50FT. GALV GARDEN FENCE SIZE:28" X 50 FT.
Brand: Mazel Part Number: 50905028
GALVANIZED GARDEN FENCE - Sturdy garden fence with graduated spacing ~ Smaller at bottom for maximum protection ~ Galvanized for corrosion resistance | *$22.64 |
 | 28IN. X50FT. GR VINYL GARDEN F SIZE:28" X 50 FT.
Brand: Mazel Part Number: 50905028G
GREEN VINYL GARDEN FENCE - Attractive garden fence with graduated spacing ~ Smaller at bottom for maximum protection ~ Green vinyl coating for corrosion resistance | *$30.13 |
 | 3 Ton Chain Hoist
Brand: Boston Industrial Model: CH3 | *$45.95 |
| 3'W Machinery Wire Fence Partition Panel
Brand: Wireway Husky Part Number: G0305
Machinery Partition Panel Provides a barrier between employees and potential hazards. Meets OSHA regulations for guarding dangerous machinery, conveyor belts and electrical switchgear and EPA hazardous waste storage standards. Durable woven 10 gauge wire construction provides clear visibility. Partitions can be easily installed for quick removal or more permanently for maximum security with all supplied hardware. Panels measure 5'H and attach to post 1' above floor for sweep space. Easy to install, remove or expand. Bright yellow enamel finish. | *$73.95 |
 | 3-Point Post Hole Digger, Model# FM5500
Brand: Northern Tool Equipment
Heavy-duty commercial gearbox with 3:1 gear ratio develops 729 ft.-lbs. of torque at 180 RPM. Shielded drive shaft with commercial-grade cross journals and quick-disconnect lock ring design for tractor connection. 3-point Category I linkage; Category II requires bushings. Boom and U-frame assemblies of 2 7/8in. diameter structural pipe. 6in., 9in. and 12in. augers sold separately. Auger Type: PTO, 3 - Point, Gear Ratio: 3:1, Torque (ft./lbs.): 729, Auger Bit Length (in.): 42, Auger Diameter Capability (in.): 6, 9, 12, Tube Size (in.): 2 7/8 | *$419.99 |
 | 3/4" Burgundy Polytape for Electric Fence
Brand: LACME
This roll of 3/4 Burgundy polytape has excellent visibility due to its unique color. It is great to use for subdividing horse pastures or for temporary grazing. This polytape has 7 tinned copper wires for excellent conductivity with a breakstrength of 485 lbs and comes in rolls of 656 feet. I don't think that you will find any other place that offers Burgundy colored polytape for your pastures. You can only get it at the Farm Supply Store. | *$15.00 |
 | 3/4" White Polytape for Electric Fence - Ruban R20
Brand: LACME
You are looking at a roll of 3/4 Polytape with 5 stainless steel wires. This Polytape is excellent for temporary fence or controlled grazing. It has the same visibility as most expensive 3/4 tapes and the 5 wire provides excellent control of trained animals yet reduces your overall fence cost. It is very easy to re-spool and it has a UV inhibitor added to extend its life. It has 250 lb breakstrength. | *$15.00 |
 | 3/4" White Polytape for Electric Fence - Rublanc 20
Brand: LACME
You are looking at a roll of Rublanc 20, 3/4 inch polytape. This Polytape is excellent when used to divide up pastures, horse fences, traffic lanes and controlled grazing. It is very easy to re-spool and it has a UV inhibitor added to extend its life. | *$15.00 |
 | 3/4" White Polytape w/ Blue trim - Reinforced Rublanc 20 for Electric Fence
Brand: LACME
You are looking at a roll of Reinforced Rublanc 20 3/4 inch Polytape with 7 tinned copper wires. This is essentially the same type of polytape as the Rublanc 20 but it is reinforced and used in extreme conditions and high wind situations. | *$15.00 |
 | 36IN. 2X4 14GA 50FT. WELD FABR SIZE:36"X 50 FT. DESC:14 GA-2"X4"
Brand: Mazel Part Number: 8050503624
WELDED UTILITY FABRIC - Galvanized before fabrication ~ Provides a versatile low-cost material ~ Use for enclosing protecting reinforcing ~ Partitioning backstops tennis courts ~ Tree window guards ~ DESC gives wire gauge and spacing size ~ Sold by the roll with retail price by the foot | *$37.09 |
 | 3x100 BLK Silt Fencing
Brand: Midwest Air Technologies Part Number: 883131A
3' x 100', Black Silt Fencing, Contractor Grade, Designed To Prevent Soil Loss At Work Site, Woven Geo-Textile That Allows Fluid To Pass Blocking Soil Particles. | *$27.19 |
| 4'W Machinery Wire Fence Partition Panel
Brand: Wireway Husky Part Number: G0405
Machinery Partition Panel Provides a barrier between employees and potential hazards. Meets OSHA regulations for guarding dangerous machinery, conveyor belts and electrical switchgear and EPA hazardous waste storage standards. Durable woven 10 gauge wire construction provides clear visibility. Partitions can be easily installed for quick removal or more permanently for maximum security with all supplied hardware. Panels measure 5'H and attach to post 1' above floor for sweep space. Easy to install, remove or expand. Bright yellow enamel finish. | *$93.95 |
 | 40ft NEW Steel Storage Container
Brand: ASCC 1-866-726-5067
This container is located in Long Beach CA We sell containers in 43 other location please acquire for other locations. Shipping using a tilt bed truck is available please contact me for a quote on trucking. 1-866-901-4526. This sale is for one New 40 foot Cargo Box / Shipping Container. These containers can be used for many uses such as: Backyard Storage, Temporary Offices or Storage for Construction Sites. The typical dimensions of a 40 foot container are 40'-0" in length 8'-0 width and 8'-6 in height. These boxes are very well constructed as they were made to be stacked up to 6 containers high on ships that travel across oceans. They are constructed with a steel frame, steel siding and the floors are constructed of 18 ply epoxy marine plywood. The picture shown may not the actual container for sale but is consistent with the type of containers we sell. | *$4,250.00 |
| | 41 IN POLYPOST STEP IN WHITE 50
Brand: Twin Mountain Fence D Part Number: TP434
Plastic Post With Steel Point At End. Fence post used in temporary fencing for wires and tapes. Fence post for temporary fencing. | *$5.29 |
